CAN I INSTALL A BATH TUB MYSELF?

Can I Install A Bath Tub Myself?

Can I Install A Bath Tub Myself?

Blog Article

Visit Our Site

On this page down the page you'll find a bunch of professional facts concerning How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


How to Install a Bathtub Yourself
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old bath tub with a new one is additionally a moderately hard job. If the old bathtub is easily obtainable, the job can relocate rapidly; if you have to open a wall surface to eliminate the old bathtub and place the new tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly require an assistant to leave the old bathtub and also set in the brand-new one. Make sure you have actually qualified on your own for the job and also are comfortable trying it. Instead of working with a specialist to take control of a halfway-completed job, it is far better to think about using one before you start. Possibilities are you might need a specialist plumber to make tube connections.
This post will assist you mount a new bath tub in your bathroom if you have actually already purchased a brand-new tub as well as do not need to transform the arrangement of your previous water system pipelines.
Your tools and also material checklist need to comprise the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be quite problematic because of the restricted gain access to that is commonly the instance.
    Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the remaining water that will come from the pipes. Once the supply pipes have been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
    Before proceeding to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.

    Suitable New Touches


    If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end supplies a link to the existing supply pipelines.
    If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
    Next off, position the tap in the mounting hole in the bath/basin ensuring that the washers remain in area in between the faucet as well as the sink. Protect the tap in place with the maker supplied backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The previous type ought to be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Installing the Bathtub


    Making use of both wooden boards under its feet, place the bath tub in the needed setting. The wooden boards are handy in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little points.
    The next objective is to guarantee that the tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub up until the spirit level checks out level.
    To mount faucets, fit the bottom of the outermost versatile faucet port to the suitable supply pipeline by making a compression sign up with; then do the very same for the other faucet.
    Turn on the water supply and also inspect all joints and also new pipework for leaks as well as tighten them if necessary. Load the bathtub as well as likewise examine the overflow electrical outlet and the typical outlet for leakages.
    Finally, take care of the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub must wait until the bath tub has been utilized at least once as this will certainly settle it right into its final setting.

    Preparing for the Setup


    To start with, the supporting structure supplied with the bathroom should be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make sure that if the tap features a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
    Fit the adaptable faucet connectors to the bottom of both faucets using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of all of the supplied washers.
    Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.

    Tiling Around the Bathtub


    In the area where the bathroom satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bath and the tiling, causing issues with wetness and also feasible leakages to the ceiling listed below.
    You can select from a range of coloured sealants to blend in your fixtures and installations. They are marketed in tubes and also cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to enable the motion experienced when the tub remains in use. The sealant can crack rather very early if you do not take into consideration this motion before sealing.
    Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or water resistant adhesive and also cement.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    A Step-by-Step Guide to Installing a Bathtub

    I found that post about A Step-by-Step Guide to Installing a Bathtub when doing research the internet. Loved our blog posting? Please share it. Help other people locate it. Thanks so much for your time spent reading it.




    Give Me A Quote!


    Report this page